WELCOME TO GAINER WEBSITE !

WEBSITE MAP|ADD TO FAVOURITE|FOLLOW USfacebookTwitter

KITCHEN APPLIANCE EXPERT

GAINER OFFER CUSTOMRS EXCELLENT SERVICE WOLDWIDE
Current location: Home»GAINER News » NEWS » Gainer NEWS » The working principle of meat mincer

Recommended Products

Hand blender stick HE-2021
Hand blender stick HE-2021
600W DC motor (400W/500W/750W optional) 2 speed soft-touch button Variable speed control (optional) S.S Hang-up loop for easy mounting Stainless steel stick with S.S blade
Hand blender set HE-2003
Hand blender set HE-2003
Hand blender set HE-2021
Hand blender set HE-2021
Hand blender set HE-2030
Hand blender set HE-2030
Hand blender stick HE-2006
Hand blender stick HE-2006
HE-2006 Hand Blender stick 600W DC motor (400W/500W/750W optional) 2 speed soft-touch button(normal,turbo) Variable speed control with LED blue light when power on (optional) S.S Hang-up loop for easy mounting Stainless steel stick with S.S blade
Meat Grinder HE-6002
Meat Grinder HE-6002
Hand blender stick HE-2008
Hand blender stick HE-2008
HE-2025 Hand Blender stick 600W DC motor (400W/500W/750W optional) 2 speed soft-touch button Variable speed control with LED blue light (optional) Stainless steel stick with S.S blade
Hand blender stick HE-2030
Hand blender stick HE-2030

Top articles

Latest articles

Your browsing history

    Loading...

The working principle of meat mincer

Categories: Gainer NEWSStars: 3Stars Visit: - Release time: 2014-07-30 11:33:00
Font size:【 Large Middle Small Source: Editor: Author:

When working, the first boot after discharge, because the material itself gravity and the spiral feeder is rotating, the continuously sent to the cutter blade for cutting. Because the back screw feeder of the pitch should be better than the small front, but behind the spiral shaft diameter larger than the previous, this causes the pressure to some materials, the force has been chopped meat is discharged from the holes in the lattice board.
For the production of canned luncheon meat, fat and lean to fine coarse ground to ground, to change the way to achieve the coarse grid plate cutter and fine twisted needs. Grid plate holes in different specification, usually used as a coarse cutter diameter holes 8 mm to 10 mm, thin cutter with a diameter of 3 mm to 5 mm. Grid plate coarse cutter and fine twisted, its thickness is 10 mm to 12 mm Common plate. Due to the coarse cutter aperture, discharging more easily, so the spiral feeder speed than that of fine twisted is faster, but less than 400 rpm. General in the 200-400 rpm. Because the lattice plate hole total area, namely the discharge amount, when the feeding screw rotation speed is too fast, so that the material jam in the cutter nearby, causing a sudden increase in load, has a bad effect on the motor.
Cutter blade is installed along the cutter. Use the tool steel cutter, knife edge sharp, use a period of time after the edge, blunt, at this time should be changed to a new blade or re grinding, otherwise it will affect the cutting efficiency, and even make some material not chopped after discharge, but by extrusion, ground into a slurry discharge, directly affect the quality of the finished product, according to research some factory quality accident, canned luncheon meat fat severe precipitation, often with this reason.
Assembly or replacement of reamer, must tighten fastening nuts, to ensure grid plate does not move, or between Inge plate moving and reamer rotating relative movement, also can cause the material grinding effect. Reamer must be tightly and lattice board, or will affect the cutting efficiency. The spiral feeder is rotated in the wall, to prevent the spiral appearance and the wall together, if slightly touching, damage to the machine immediately. But the gap is not too large, it will affect the feeding efficiency and extrusion pressure, even make the material flow from the gap, so higher requirements for fabrication and installation of this part of the components of the.

ABOUT Gainer

Shenzhen Gainer Electrical Appliances CO, .LTD was established in 2010 and sites in Shenzhen, China. Has 4 years of history. We operates in a modern 7500 square meter facility with room including injection shop, assembly line, R&D, laboratory. Our company is a set design, production, manufacturing in one of the enterprises, specialized in small home appliance, such as hand blender ,meat grinder, food processer, etc...

LEARN MORE+

LEAVE YOUR MESSAGES

Hello! Can I help you choose a product?

  • *
  • *
Website mapcnzzCopyright © Shenzhen Gainer Electrical Appliances CO, .LTD All Rights Reserved